Skip to main content

Usage of ECDIS - Not as anticipated - A report

ECDIS Not Being Used as Anticipated


The U.K. Marine Accident Investigation Branch (MAIB) has announced that it is conducting a safety study, in collaboration with the Danish Maritime Accident Investigation Board, to understand why operators are not using ECDIS as envisaged by regulators and the system manufacturers. 
The news follows the release of a MAIB investigation report into the grounding of the bulk carrier Muros. In the early hours of December 3, 2016, the Muros ran aground on Haisborough Sand, eight miles off the Norfolk coast. 
When Muros grounded, she was following a passage plan shown on its electronic chart and display information system (ECDIS). The MAIB investigation found that:
• The vessel was following a planned track across Haisborough Sand. The passage plan in the ECDIS had been revised by the second officer less than three hours before the grounding and it had not been seen or approved by the master.
• A visual check of the track in the ECDIS using a small-scale chart did not identify it to be unsafe, and warnings of the dangers over Haisborough Sand that were automatically generated by the system’s ‘check route’ function were ignored.
• The second officer monitored the vessel’s position using the ECDIS but did not take any action when the vessel crossed the 10-meter safety contour into shallow water.
• The effectiveness of the second officer’s performance was impacted upon by the time of day and a very low level of arousal, and she might have fallen asleep periodically.
• The disablement of the ECDIS alarms removed the system’s barriers that could have alerted the second officer to the danger in time for successful avoiding action to be taken.

The MAIB has recently investigated several grounding incidents in which the way the vessels' ECDIS was configured and utilized was contributory. There is increasing evidence to suggest that first generation ECDIS systems were designed primarily to comply with the performance standards required by the IMO, as these systems became a mandatory requirement on ships, with insufficient attention being given to the needs of the end user, states the report.
“As a consequence, ECDIS systems are often not intuitive to use and lack the functionality needed to accommodate accurate passage planning in confined waters. This situation has led to seafarers using ECDIS in ways which are at variance with the instructions and guidance provided by the manufacturers and/or expected by regulators.” 
to get the full report - visit us at www.shipaxis.in

Comments

Popular posts from this blog

Autonomous ship navigation study begins

BMT’s Rembrandt simulator will be combined with ASV Global’s autonomous vessel control simulator A group of UK-based companies has started a new £1.2M (US$1.6M) research project to investigate how autonomous vessels could co-exist with manned ships. BMT has teamed up with ASV Global and Deimos Space UK for the Shared Waterspace Autonomous Navigation by Satellite (Swans) project. With funding from Innovate UK these companies will investigate how autonomous surface vessels (ASVs) can use existing and future satellite capabilities for collision avoidance and communications. This is particularly focused on autonomous vessels operating beyond the horizon of shore and in congested maritime traffic, BMT managing director Phil Thompson explained, adding that the few autonomous vessels already developed use the global automatic identification system (AIS) for collision avoidance. “But they remain at risk of colliding with vessels or objects not using AIS,” he said in a statement...

Suppliers and owners tackle vessel remote control challenges

Suppliers and owners tackle vessel remote control challenges GulfMark Offshore’s Highland Chieftain in the North Sea was controlled from a workstation in California in August Rolls-Royce, Wärtsilä and Navtor have demonstrated technologies for remotely controlling different types of workboats Technology providers plan to work closely with shipowners during 2018 to tackle some of the challenges emerging as remote control and autonomous ships are developed. These include providing greater and more accurate information to vessel operators, developing better anti-collision programs and producing physical feedback to controllers. In 2017, Rolls-Royce collaborated with Danish tug owner Svitzer and class society Lloyd’s Register to develop a method of controlling a harbour tug from a remote control room.  Marine Electronics & Communications  saw this in action in Copenhagen, Denmark, on 16 November when a tug master successfully controlled the 2016-buil...

Norway Opens New Test Area for Autonomous Ships

Norway has opened an autonomous shipping test bed in Horten on the Oslofjord, Kongsberg said. The test bed, officially opened on December 6, is the third of its kind in the country and the fourth such approved area in the world. Established to support the growth in the development of new solutions for autonomous maritime operations, the new area is open to both Norwegian and international organizations. As explained, the area is designed to be  “a convenient, safe, non-congested space to trial new technology and vessels.” The area is specially designated for autonomous trials by the Norwegian Maritime Administration and the Norwegian Coastal Administration. The initiative to establish the new test bed was undertaken by maritime technology company Kongsberg, the town of Horten, classification society DNV GL, Norwegian Defence Research Establishment (FFI) and the University College of South East Norway. The introduction of the test bed follows the last year’s openin...